PDA

View Full Version : motor hesiotating

94greenhunter
10-18-2007, 08:40 AM
i just got done rebuilding my motor and now it is starting to hesitate. I need so help in to why it is doing that. i did not change anything in the motor but i do not know what it could be.
Darren
10-18-2007, 08:43 AM
did you set the timing?
cracker
10-18-2007, 10:51 AM
did you set the timing?

:werd: Mine hesitated all the time until i advanced the timing a few degrees, and hasnt done it since. Good luck.
speedfreak87
10-18-2007, 02:16 PM
timing.
94greenhunter
10-18-2007, 07:51 PM
well i did not take my distributor out or mess with my timming and it should be at top dead center so i do not think that is it but i will check that. but what else could it be.
Masshole
10-18-2007, 07:58 PM
well what do you have done and what is the timing currently set at??
MichaelsLilGray
10-18-2007, 10:36 PM
...When you say rebuild what are you talking about... like all the way to the heads? If its hesitating.. like my 95 did.. its a low compression in one of the cylinders. That can cause it to stutter and hesitate a bit. if you machined the heads and such.
MichaelsLilGray
10-18-2007, 10:37 PM
well what do you have done and what is the timing currently set at??

Dean its 9:35PM :lol:
speedfreak87
10-18-2007, 10:53 PM
well i did not take my distributor out or mess with my timming and it should be at top dead center so i do not think that is it but i will check that. but what else could it be.

It could be fuel pressure. (IE pump going bad, clogged filter)
cracker
10-19-2007, 02:19 AM
Just check it with a timing gun real quick to determine where your at. I have mine set at 14* or 15* i dont remember exactly anymore. But yes it could be a ton of other things. Hows the harmonic balancer doing? I dont think that has been brought up yet.
Darren
10-19-2007, 07:08 AM
well i did not take my distributor out or mess with my timming and it should be at top dead center so i do not think that is it but i will check that. but what else could it be.

How do you rebuild a motor without removing the distributor? I was having problems with my distributor comming loose untill I used thread locker on the bolt that holds it. maybe its just loose
94greenhunter
10-19-2007, 07:47 AM
all i did was change the gaskets on the motor. but yea i took the heads off of it. but it only hesitates every now and again. but when i get home i will check the timming on it to make sure that it is still where i put it. but thanks for all the help you guys are giving me.
speedfreak87
10-19-2007, 01:16 PM
I'm very confused.. if you took the heads off, the dizzy had to come out since you would have to remove the intake. I would pull the dizzy, bring the #1 cyl to TDC and reinstall the dizzy pointing to the #1 cyl.
Darren
10-19-2007, 01:18 PM
I'm very confused.. if you took the heads off, the dizzy had to come out since you would have to remove the intake. I would pull the dizzy, bring the #1 cyl to TDC and reinstall the dizzy pointing to the #1 cyl.

On the compression stroke
Darren
10-19-2007, 01:19 PM
Its probably good as far as that or it wouldnt run. Prolly just needs to be set
cracker
10-19-2007, 02:09 PM
Its probably good as far as that or it wouldnt run. Prolly just needs to be set

:werd:
94greenhunter
10-21-2007, 11:30 PM
well my smog pump just went out. it locked up on me. could that have been the reason it has been hesitating.
speedfreak87
10-22-2007, 12:01 AM
it is possible, but if it seized up you would have known about it right away.
94greenhunter
10-22-2007, 10:28 PM
it did i ended up on the side of the road. but what i was woundering it could it have been catching and it boggin my motor down. but now i need to find a used smog pump that works so i can get it back on the raod. i do not want to buy a new one because i am just going to completely take it off sooner or later but i need it to pass inspection before i do that.
speedfreak87
10-22-2007, 10:32 PM
it's possible, but not likely. anything could happen though.

don't put another one on, just buy a shorter belt and bypass it.
94greenhunter
10-22-2007, 10:46 PM
i wish i could but it will not pass the state inspection. i thought about that, but it will not work because of the way my belt goes through it.
my86gt
10-22-2007, 10:47 PM
it's possible, but not likely. anything could happen though.

don't put another one on, just buy a shorter belt and bypass it.

:werd: what the freak said. :lmao1:
Darren
10-23-2007, 06:48 AM
I may have a used one here somewhere. I'll have to look for it and let you know
94greenhunter
10-25-2007, 07:55 PM
never mind i got one but thanks any way. i just drove it to work from houston texas to galiano louisiana. that is about 370 miles and it did just fine. so i do not know what it could of been.
cjs03gt
10-25-2007, 08:40 PM
My car was doing the same thing, and it was my fuel filter clogged up with sand. Now it's fine.
94greenhunter
10-25-2007, 08:45 PM
dang well i know it is not the fuel filter because it is new. but it is running good now so i hope it keeps it up
speedfreak87
10-25-2007, 11:08 PM
bugs. hope it stays running good for you.
94greenhunter
10-27-2007, 11:33 PM
yea me too