hey Cobra's whats your combo?

[BLWN 05]

4.30's+Vortech+470 RWHP= :snicker:

[grendel]

avg bolt on cobra 460/490 on slipping clutch

[TRM8ER]

2.2KB w/2.93 upper = 556/545 :wink:

[TJVineyard]

04 with the black supercharger option. :D

TJ

[Shane361]

4lb lower 2.8 upper 476rwhp and 481rwtq, Kenne Bell inroute for over 600rwhp-Shane

[BLWN 05]

Getting ready to pick up a CHP 5.1L stroker motor, Bassani Mid's... so I should be in the 600RWHP range by March.. :)

[Nazman]

With a few bolt-on's 459RW on motor.......with a little juice 628RWHP. :mick:

Naz

[95 Sleeper]

A little 302, with 6 pounds of boost making over 500 rwhp/tq with 93 octane fuel

[leedog]

4lb lower 2.8 upper 476rwhp and 481rwtq, Kenne Bell inroute for over 600rwhp-Shane
NOICE! Gonna drive it to V-Town when its done?

[MarcInJapan]

DiabloSport Predator Custom Tuned by Coastal Dyno
2.93 Upper Pulley
MotoBlu Idler
Accufab Single Blade Throttle Body and Intake Plenum (Polished)
Apten Stage I Ported Eaton Supercharger (Intake Plenum Port-Matched)
Mac Cold Air Intake
Bassani X Pipe without Cats
Flowmaster Cat-Back Exhaust
LFP Supertank Reservoir
LFP Water to Air Intercooler
Innovate LM1 WideBand Air/Fuel Meter with Datalogging & External Aux Inputs

471HP and 477 Torque.

Ordering a 4lb lower pulley kit tomorrow. After install going to tune it on the dyno. Should be close to the 500HP/Torque range.

[Driver13]

bone stock (I've only had it for 2 weeks fellas!)
SLP o/r X and FR500 catback sitting in garage.

[BadMoFo]

2.76 Billetflow pulley/w idlers
jlt rai
mac o/r h pipe
flows
spec stage III+ clutch
fidanza alum flywheel
26 spline input shaft
mgw shifter w/ pistol grip


500 rwhp and 506 rwtq, yes I know its a freak.

[BLWN 05]

Nice numbers here... looks like most of us are around 460-500 RWHP... :mick:

[blown98cobra]

507/440something I need more

[jhennessy]

I have Cobra envy... :drool:

[The Punisher]

Whipple SC 2300AX
Bassani w/o cats
60 lb injectors
Twin SVT focus fuel pump
Kenne Bell boost?
Reichard Pulley
Eibach springs
Black FR500's

[64comet]

2.8", Cold air, basani X and Borla catback, tune

456/480 or so. Should be a little higher since dyno was with stock H-pipe and more restrictive catback.

[cobracomp]

2.7, flows, k&n,sct dyno tune 91 octane,sct 2400 maf, 459rwhp,485trq. :wave:

[TrueBlueVenom]

all motor here... and staying all motor:

currently:
-suspension work (H&R Race springs, FL SFCs, buncha other stuff)
-L/Ts, ProChamber, Bassani catback
-minor stuff

getting installed:
-forged pistons and h-beam rods
-ported heads
-Stage 3 Crowers
-4.30s
-IRS bracing and bushings
-03/04 Cobra halfshafts (new pair)

[10thsvt]

In sig.. :mick: